1/8 DIN Temperature Controllers

FuzyPro 1/8 DIN Temperature Controller Heat/Cool Controllers are designed to provide precise control with a quick and easy set up procedure. SMT and microprocessor technology provides all these features plus reliability and economy. LED index indication allows full viewing and selection of parameters. 

The dual display allows set point and process value visibility at all times. An advanced software algorithm automatically calculates all PID parameters to eliminate complicated manual tuning efforts. Automatic tuning can be bypassed if manual tuning is preferred. An open-loop, manual mode can be initiated if the sensor fails. Front panel electronic calibration sensor linearization self-diagnostic capabilities and cold junction compensation are all performed by the single chip microprocessor. The in-panel depth is only 2-1/2-in. 

FuzyPro 1/8 DIN Temperature Controller Heat/Cool Controllers Features:

  • Automatic tuning of PID parameters 
  • Selectable input 
  • Dual heating and/or cooling outputs with 2 alarms 
  • ºF or ºC display. Dual display. Sealed mylar front panel 
  • Security code protection, automatic manual mode operation 
  • All control parameters adjustable from front panel 
  • 3 year warranty. 2-1 /2-in. in panel depth

FuzyPro 1/8 DIN Temperature Controller Heat/Cool Controllers Specifications:

INPUT 
Thermocouple Type J,K,T,B,E,R,S,N (selectable) 
RTD PT 100 ohm(DIN or JIS) 
Linear -10-60mV Configurable input other voltage or current 
Display  Temperature or engineering units 
Outputs Single output with 2 optional independent alarms
Heating and/or cooling outputs with 2 optional alarms 
Relay SPST relay rated 3A, 240V maximum resistive load 
Pulsed Voltage  32VDC, 20mA maximum ohms
Current 4-20mA, 0-20mA maximum load 500 ohms 
Voltage 0-10V minimum load 500K ohms 
Alarms 8 selectable modes each alarm 
SPST relay(s) rated 2A, 240V maximum resistive load 
CONTROL FEATURES 
Temp Range  Selectable Set Point:
-1999ºF - 3182ºF (-1128ºC - 1750ºC)
Alarm Set Point  Full Range Adjustable
Control Modes Controls can be configured as On/Off Proportional(P)
Proportional with manual reset Proportional/Integral(PI)
Proportional Derivative(PD)
Proportional/Integral/Derivative(PID) Heating and Cooling
Proportional Band:O-100% of span 
Integral (Reset)   0-3600 seconds
Derivative (Rate) 0-1000 seconds 
Anti-Reset Wind-Up Inhibits integral action outside of proportional band 
Cooling Adjustable deadband from -10 to + 10% of cooling proportional band 
Manual Mode  Configurable as open loop control should sensor no longer function
Cycle Time 0 - 120 seconds 
Sensor Break Protection Configurable status of control and alarms 
Control Action Selectable-Direct action for cooling
Reverse action for heating
 
INDICATION
Display  4 digit red 5/8-in. LED Process Value Display. 
Green 1.2-in. LED Set Value display 
Selectable decimal placement for normal or high resolution display
Example  0000, 000.0, 00.00, 0.000
F / C  Selectable with 2 LED indicators
Sample Rate 250 milliseconds 
Power Supply  90-26OVAC, 50/60Hz Consumption: less than 5VA
Data Retention 10 years (EEPROM) 
Control Stability + -0.15% of full scale 
Accuracy + -0.25% of range: + -1 c or 0.5C in high resolution 
Cold Junction Compensation 0.1% ambient 
External Resistance 100 ohms maximum 
Common Mode Rejection  120dB
Normal Mode Rejection  60dB
Input Impedance 10M ohms
Operating Temperature  14ºF - 122°F (-10ºC - 50°C)
Humidity  0-90% RH (non-condensing)
Insulation 20M ohm minimum (5OOVDC) 
Breakdown 2OOVAC, 5O/60Hz 1 minute 
Vibration 10-55Hz amplitude 1 mm
Shock  200m/c(20g)